Prediction of the load-bearing capacity of curved rotating reinforced discs made of rigid-plastic various-resistance materials
- 作者: Yankovskii A.P.1
-
隶属关系:
- Khristianovich Institute of theoretical and applied mechanics the Siberian Branch of the RAS
- 期: 编号 4 (2025)
- 页面: 80-114
- 栏目: Articles
- URL: https://modernonco.orscience.ru/1026-3519/article/view/690609
- DOI: https://doi.org/10.31857/S1026351925040051
- EDN: https://elibrary.ru/bnkpvr
- ID: 690609
如何引用文章
详细
A problem on a conditional extremum is formulated, which allows one to determine, based on the second limiting state, the upper limit of the maximum angular velocity of rotation of an axisymmetrically curved, fiber-reinforced disk. The structure is rigidly fixed to the vase or hub; blades can be attached to the outer edge of the disc blade. The materials of the components of the composition are assumed to be rigid-plastic, having asymmetry under tension and compression; the material of the binding matrix may have cylindrical anisotropy. Plastic deformation of the components of the composition is associated with piecewise linear yield criteria. The reinforcement structures of the disc web have meridional symmetry. A two-layer model of a curved disk with a plane-stress state in each of the fictitious composite layers is used. The discretized problem is solved using the simplex method of linear programming theory. The developed numerical algorithm has been verified. Examples of numerical calculation of the maximum angular velocity of rotation of flat, conical and spherical homogeneous and composite disks with different degrees of their curvature are analyzed. The cases of reinforcement of the disk web along geodetic directions and logarithmic spirals, as well as along meridional and circular trajectories, were investigated. The comparison was carried out for disks of the same mass with the same consumption of reinforcement. It has been shown that composite disks with a meridional-circumferential reinforcement structure have the highest load-bearing capacity. It has been demonstrated that even a slight axisymmetric curvature of the disk web leads to a sharp decrease in its load-bearing capacity compared to a similar flat structure.
作者简介
A. Yankovskii
Khristianovich Institute of theoretical and applied mechanics the Siberian Branch of the RAS
编辑信件的主要联系方式.
Email: yankovsky_ap@itam.nsc.ru
Novosibirsk, Russia
参考
- Ponomarev S.D., Biderman V.L., Likharev K.K., Makushin V.M., Malinin N.N., Feodos′yev V.I. Calculations for strength in mechanical engineering. Vol. III. Inertial loads. Vibrations and shock loads. Endurance. Sustainability. М.: MASHGIZ, 1959. [in Russian].
- Birger I.A., Dem’yanushko I.V. Calculation for the strength of rotating disks. М.: Mashinostroenie, 1978 [in Russian].
- Vasiliev V.V., Protasov V.D., Bolotin V.V. et al. Composite Materials, Reference book / Ed. by V.V. Vasiliev, Yu.M. Tarnopol′skii. М.: Mashinostroenie, 1990 [in Russian].
- Karroll-Porczynski C.R. Advanced Materials. Refractory Fibres, Fibrous Metals Composites. Guildford: Astex Publishing Company Ltd., 1962.
- Weeton L.W., Scala E. (ed.) Composites: State of Art. New York: Metallurgical Society of AIME, 1974.
- Composite materials. Handbook / Ed. by D.M. Karpinos. Kiev: Naukova dumka, 1985 [in Russian].
- Grigorenko Ya.M. Isotropic and anisotropic layered shells of rotation of variable rigidity. Kiev: Naukova dumka, 1973 [in Russian].
- Takkar S., Gupta K., Tiwari V., Singh S.P Dynamics of rotating composite disc // J. Vib. Eng. Technol. 2019. V. 7. № 6. P. 629–637.
- Rahi A. Lateral vibrations of a microrotating shaft-disk system subjected to an axial load based on the modified strain gradient theory // Mech. Adv. Mater. Struct. 2019. V. 26. № 20. P. 1690–1699.
- Semka E.V., Artemov M.A., Babkina Y.N., Baranovskii E.S., Shashkin A.I. Mathematical modeling of rotating disk states // J. Phys: conf. Ser. 2020. V. 1479. № 1. P. 12122. https://doi.org/10.1088/1742-6596/1479/1/012122.
- Koo K.-N. Influence of rotation on vibration characteristics of thick composite disks// Mech. Adv. Mater. Struct. 2020. V. 27. № 8. P. 676–686.
- Farukoğlu Ö.C., Korkut I. On the elastic limit stresses and failure of rotating variable thickness fiber reinforced composite disk // ZAMM. 2021. V. 101. № 9. E202000356. P. 1–18.
- Wang B., Wang G., Shi Y., Huang L., Tian K. Stress-constrained thermo-elastic topology optimization of axisymmetric disks considering temperature-dependent material properties // Mech. Adv. Mater. Struct. 2022. V. 29. № 28. P. 7459–7475.
- Yankovskii A.P. Building a complete solution to the problem of determining the bearing capacity of a flat reinforced rotating disk // Vycisl. meh. splos. Sred. 2023. V. 16. № 3. P. 289–309.
- Romanova T.P. Rigid-plastic behavior and bearing capacity of thin flat reinforced rotating disks // Mech. Adv. Mater. Struct. 2024. V. 31. № 30. P. 12721–12739. https://doi.org/10.1080/15376494.2024.2328751
- Yankovskii A.P. Numerical method for determining the load capacity of flat rotating reinforced discs // Vycisl. meh. splos. Sred. 2024. V. 17. № 3. P. 290–307.
- Erkhov M.I. Theory of ideally plastic bodies and structures. M.: Nauka, 1978 [in Russian].
- Ishlinskiy A.Yu., Ivlev D.D. Mathematical theory of plasticity. M.: Fizmatlit, 2001 [in Russian].
- Chakrabarty J. Applied plasticity. 2nd ed. New York: Springer, 2010.
- Novozhilov V.V., Chernykh K.F., Mikhailovsky E.I. Linear theory of thin shells. Leningrad: Polytechnica, 1991 [in Russian].
- Romanova T.P., Yankovskii A.P. Investigation of load-bearing capacity of rigid-plastic reinforced ellipsoidal shells of rotation // Mech. Adv. Mater. Struct. 2023. V. 31. № 18. P. 4387–4398.
- Romanova T.P., Yankovskii A.P. Load-bearing capacity of rigid-plastic reinforced shallow shells and plates // Mech. Adv. Mater. Struct. 2022. V. 29. № 26. P. 5651–5665.
- Nemirovskii Yu.V., Yankovskii A.P. Some features of the equations of shells reinforced with fibers of constant cross-section // Mech. Compos. Mater. Struct. 1997. V. 3. № 2. P. 20–40.
- Banichuk N.V., Kobelev V.V., Rikards R.B. Optimization of structural elements made of composite materials. M.: Mashinostroenie, 1988 [in Russian].
- Hu L.W. Modified Tresks’s yield condition and associated flow rules for anisotropic materials and applications // J. Franclin Inst. 1958. V. 265. № 3. P. 187–204. https://doi.org/10.1016/0016-0032(58)90551-9
- Ramu S.A., Iyengar K.J. Plastic response of orthotropic spherical shells under blast loading // Nucl. Eng. Des. 1979. V. 55. № 3. P. 363–373. https://doi.org/10.1016/0029-5493(79)90115-8
- Onat E. The plastic collapse of cylindrical shells under axially symmetrical loading // Quarterly of Applied Mathematics. 1955. V. XIII. № 1. P. 63–72.
- Nemirovskii Yu.V. Limit equilibrium of multi-layer reinforced axisymmetric shells // Izv. AN SSSR. MTT. 1969. № 6. P. 80–89.
- Romanova T.P., Yankovskii A.P. Piecewise-linear yield loci of angle-ply reinforced medium of different-resisting rigid-plastic materials at 2D stress state // Mechanics of Solids. 2020. V. 55. № 8. P. 1235–1252.
- Samarskii A.A. The theory of difference schemes. New York, Marcel Dekker Inc., 2001.
- Zuhovickii S.I., Avdeeva L.I. Linear and convex programming. M.: Nauka, 1964 [in Russian].
- Il′yushin A.A. Proceedings (1946–1966). V. 2. Plasticity. M.: Fizmatlit, 2004 [in Russian].
- Vasiliev V.V., Morozov E. Advanced Mechanics of Composite Materials and Structural Elements. Amsterdam: Elsever, 2013.
- Carmo M.P. Differential geometry of curves and surfaces. New Jersey: Prentice-Hall Inc., 1976.
补充文件
